Hybrid View
-
27-12-2010 #1
I am afraid CNCDudeZ website is down and hasnt been updated for a while. You could try PM'ing CLaNZeR (CNCDudeZ) direct but he's not been around for a while and I don't think he supports this project any more.
Moderators
-
27-12-2010 #2
Hi welcome back Sean... Google was reporting the .co.uk site as off the air earlier today when i tried it...said their last cache was the 14th December..
-
28-12-2010 #3
-
28-12-2010 #4
-
28-12-2010 #5
Hey welcome back Sean and when you popin in for this cup of tea on the way through Swindon?
PaulIf the nagging gets really bad......Get a bigger shed:naughty:
-
29-12-2010 #6
No worries Sean good to hear you still about.
If the nagging gets really bad......Get a bigger shed:naughty:
-
12-01-2011 #7
Hello Lee,
i'm currently working on a software that should control 4 motors for a wire machine using our software, see the software here
we really would like to sell the software with a dedicated hardware for controlling the 4 stepper and the question is
if your development could be used as a starting point for this and how much it would cost.
As you can see, we need 4 motor axis direction control, and we could use some others i/o for heating the wire and limit control.
if you have interest in this project please contact me at [email protected]
Thank you for your timeLast edited by Lee Roberts; 26-03-2019 at 10:28 PM.
-
04-04-2011 #8
In the first place happiness for their project. I am a student that I would like to carry out this badge USB. The problem is that my parallel port is different and therefore I cannot make it. My parallel port is the following one:
Pin1 X Step
Pin2 Y Enable
Pin3 Y Dir
Pin4 Z Dir
Pin5 Z Step
Pin6 Z Enable
Pin7 X Dir
Pin8 Y Step
Pin9 spindle MOTOR
Pin10 X Home
Pin11 Y HOME
Pin12 Z HOME
Pin13 EStop
Pin14 X ENABLE
Pin15 EXPAND
Pin16 EXPAND
Pin17 EXPAND
Pin18 to Pin25 GND
The Firmware could send me for the PIC 18F4550.
THANK YOU
-
The Following User Says Thank You to JAVIER For This Useful Post:
-
06-04-2011 #9
surely it would be easier to make a custom parallel cable to correct the pinouts rather than rewrite the code?
-
The Following User Says Thank You to pavlo For This Useful Post:
-
17-04-2011 #10
Hello to everybody.
I have one problem with my USB to PARALLEL Port DIY Interface. It's recognized correct on PC with Win XP but when I connect it to my laptop with Win 7/32 device has not recognized (Unknow device) as well as I connect it to my desktop PC with Win 7/64. Any sugestions?
Thread Information
Users Browsing this Thread
There are currently 4 users browsing this thread. (0 members and 4 guests)
Similar Threads
-
What is the function of a parallel port breakout board?
By hbx in forum Machine Control SoftwareReplies: 13Last Post: 12-03-2013, 06:18 PM -
Stepper motor drive using mach3 from parallel port
By hmarwat370 in forum General ElectronicsReplies: 0Last Post: 04-02-2013, 08:55 AM -
parallel port address
By Dan Brown in forum Artsoft Mach (3 & 4)Replies: 6Last Post: 07-01-2010, 12:04 PM -
Laptop, ie no parallel port?
By tompsky in forum Laptops & TabletsReplies: 3Last Post: 11-11-2008, 07:12 PM -
Which USB parallel port emulator is the best
By bruce_miranda in forum General ElectronicsReplies: 1Last Post: 18-09-2008, 03:38 PM
Bookmarks