conect 121 / cadet lathe manual/user's guide anyone?

**x-rayman** · 07-08-2016

Hello John S,

Thank you for the software and the manual I will play nicely and see if I can get it up and running.

Thanks again,

Kind regards,

Keith

**Smithy50** · 29-10-2016

Hi Everyone,

I have just acquired a Conect Cadet Plus, which is in excellent condition. I have downloaded the original software from the link in John S's reply above.

I am currently organising an old PC capable of running DOS. My intention is to try and get it running with the original software. One of the ICs (I'm guessing an EPROM) has a label on it with 'CONECT LTD V1.08 L 2/93'

I would be interested to find out how x-rayman got on with getting his lathe up and running. I would also be grateful for information from anyone who has got one of these lathes.

**x-rayman** · 30-10-2016

Hi Smithy50,
My Conect Cadet Plus is now up an running thanks to the info and software from John S.
I found that the cable required was a straight serial lead 9 pin female to 9 pin male ie wired pin for pin.
Only 4 wires are used but the complete cable is readily available and cheap.
Mine is 9800 baud but I think some of the earlier ones may have been different.
I also found that the software will run on modern computers with Windows XP, 7 ,8 and 10 32 and 64 bit using DOSbox which is a freeware DOS emulator.
Running this way allows you to use a modern cad programme like QCad which is also freeware.
The designs in the conect software are DXF files as are the templates and seem to work OK in QCad .
When the Conect software is running if you press ALT P it asks for a password which is conectl.
I am currently writing up what I did and how I set the software up, when its done I can email it if you wish.
The setup also works with modern laptops using USB to serial adaptors.

Regards,
Keith

**Smithy50** · 30-10-2016

x-rayman thanks for the prompt and helpful response.

I had a 9-pin serial cable and tried to install the software on an old laptop running DOS7 and Windows 98, but I kept getting a MetaWINDOW graphic shell missing error.

I will try it on a new PC with DOSbox as you suggest and see how it goes; and report back.

I would be very interested in how you set up the software.

Thanks Again

**John S** · 30-10-2016

I have recently gutted a brand new Conect 121 and think the boards, less spindle board which was reused may be kicking about still.

**x-rayman** · 31-10-2016

Hi Smithy50,

I found that the METASHEL (various versions and spellings) are in the downloaded software.
If you run the METASHEL.exe file it tell you how to install it.
I seem to remember using the Turning P 1.2 version of the conect software.
Best of luck,
Keith

**Smithy50** · 31-10-2016

Hi x-rayman,

Thanks for that info. I've found the metashel.exe file and installed it as a TSR and can now load and apparently run the Conect software within DOSbox on a Windows 10 PC. I just need to get a USB to Serial cable, or adapter, so that I can connect it to the lathe.

Thanks again.

**Smithy50** · 31-10-2016

Hi John S,

Are the circuit boards the same on the Conect Cadet as the Conect 121? I haven't got the software side fully sorted yet, so haven't been able to test the lathe, but I would be interested in the boards if they are the same as those in my lathe. I will take some photos of the boards tomorrow and get back to you.

Thanks

**mity** · 01-07-2022

just bought 1 today hopefuly il get this software up and running thanks guys for your sw and info its greatly appreciated

**x-rayman** · 01-07-2022

Hi,
I have found that the DOS software runs very well in the latest version of DosBox X which is free online.
My conect cadet plus runs from an RS232 card in a windows 10 PC.
All the best with your new lathe.

Keith