-
10-02-2013 #1
Gents,
I'm trying to calculate the maximum deflection of an unsupported part of a shaft with the following data:
L total unsupported length = 0.18m (not mm;))
A cross section surface (round rod) = pi * (0.01m)^2
E Young's modulus = 180GPa
F force applied to the end of shaft = 1000N (random round number)
delta (max deflection) = F*L / E*A
Now popping the values in to the equation I get that max deflection is equal:
delta = F * 3.19*10^-9 [m/N]
which basically means that with F = 1000N the deflection is
delta = 3.19 * 10^-6 m = 3.19*10^-3 mm = 0.00319mm
That is rather small, considering that 1000N is pretty much the same as 100kg weight attached to one end.
Pack of biscuits to anyone who can point an error in the above and call be stupid:)
Regards,
dsc.Last edited by dsc; 10-02-2013 at 10:29 PM.
-
10-02-2013 #2
0.18mm unsupported length?
-
10-02-2013 #3
Ha, well spotted, although it's just a unit error.
After some reading I don't think the above equation for delta is correct as there's no moment of inertia involved.
Regards,
dsc.
-
10-02-2013 #4
I just ran the figures and got 3183mm of deflection...
A = pi0.01^2 = 0.000314159
F*L = 1000 * 0.18 = 180
E*A = 180 * 0.0003blahblah = 0.05654866
180 / 0.0565blahblah = 3183.09886183
-
Perhaps you are working out how far it will stretch if you pull on the end, not how far it will bend if you load it at 90 degrees?
-
11-02-2013 #6
You could be right here Robin. Its been a very long time since I used Youngs Modulus but in this form I thought it was used for calculating a change in length due to compression or extension.
-
11-02-2013 #7
Ah yes, it's all wrong!:)
Here's the right formula (taken from http://www.clag.org.uk/beam.html):
δ = FL3 ∕ 3EI
I = πr4 ∕ 4 = πd4 ∕ 64
(for round beam)
which means that deflection at a given F and L, for a 20mm dia beam is:
δ = FL3 * 0.0002358
Assuming L = 0.18m and F=100N the maximum deflection is:
δ = 100 * 0.005832 * 0.0002358 m = 0.0001375m = 0.1375mm
Which makes much more sense than the previously calculated value.
The funny thing is that changing the dia from 20mm to 22mm gives you a maximum deflection drop from 0.1375mm to 0.094mm. That's just by making the shaft 2mm thicker. Quite amazing me thinks.
Regards,
dsc.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
How much deflection to expect...
By Wal in forum Gantry/Router Machines & BuildingReplies: 30Last Post: 04-02-2014, 10:41 AM -
screening / glitchy operation - sanity check
By dsc in forum General ElectronicsReplies: 21Last Post: 01-12-2013, 11:35 PM -
sanity check - constant running, loads and more
By dsc in forum Stepper & Servo MotorsReplies: 4Last Post: 26-11-2012, 12:26 PM -
Toroidal transformer voltages - sanity check needed!
By m_c in forum General ElectronicsReplies: 16Last Post: 03-10-2011, 08:34 PM -
Deflection in precision rod rails
By irving2008 in forum Rails, Guideways & BearingsReplies: 11Last Post: 14-03-2009, 12:01 PM
Bookmarks