Threaded View
-
10-06-2013 #1
I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.
so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes
here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits
the long side are 90 by 45 = 1450mm
there are six bits
-----------------------
the short sides are 1080mm
there are 6 bits of this - maybe 8
--------------------------
the legs are 90mm by 90mm and have bolt in feet
------------------------------------
there are 4 complete blue panels, for all 4 sides
the buttons on the front could be for auto stop
-----------------------------------------
if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers
the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft
-------------------------------------------
theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis
-------------------------------------------
there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis
-------------------------------------------
there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.
these are fitted to 4 bits of 60 by 45mm -
THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.
there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius
----------------------------------------------
also there is stack and stacks of 45mm box, lots of nuts and bolts
all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.
------------------------------------------------
there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors
two of these
and two of these, the other one is a bit bigger all full of giblets
have all the wireing and connectors too.
---------------------------------------
there are two BUSHE pumps, rams, connectors and valves
-----------------------------------
location magnet things for 3 axis, 3 on each,
also have a trend t10 1/2 inch collet 2000kw plunge router, used for about 2 hours - ten years ago, in the case.
also have a 100a invertor / tig welder plasma cutter
i really should nail together a 4foot by 2 foot plasma table........
all used
IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR
I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.
NOW THE BEST BIT i NEED
Nema23 Stepper Motor Kit 3.1Nm x 3 Axis
ALSO NEED A SPINDLE AND MOUNT
AND SOME MACH3 - OR 4
OH AND A USB/lan BOB
SO HAPPY TO HAVE A SWAPSIES.
THANKSLast edited by nobby; 10-06-2013 at 10:16 PM.
Thread Information
Users Browsing this Thread
There are currently 4 users browsing this thread. (0 members and 4 guests)
Similar Threads
-
SWAP: 2 onld controllers, 5 by 4 modular table, 4 - 4ft sliders, 2 air rams, 2 pimps, etc
By nobby in forum Items For SwapReplies: 2Last Post: 29-05-2014, 11:33 PM -
Effect of Forces on Gantry Cross-Sections?
By WandrinAndy in forum Gantry/Router Machines & BuildingReplies: 37Last Post: 22-12-2012, 10:34 PM -
Straight sections of box steel
By gavztheouch in forum Metalwork DiscussionReplies: 2Last Post: 03-01-2012, 02:37 PM -
FOR SALE: Lots of Bosch Rexroth Aluminium extrusion 50mm x 50mm.
By michael in forum Items For SaleReplies: 12Last Post: 12-10-2011, 08:52 AM -
FOR SALE: Z slides ??
By John S in forum Items For SaleReplies: 4Last Post: 27-09-2009, 11:03 PM
Bookmarks