Quote Originally Posted by nobby View Post
I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.
so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes

here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits


the long side are 90 by 45 = 1450mm
there are six bits
-----------------------
the short sides are 1080mm
there are 6 bits of this - maybe 8
--------------------------
the legs are 90mm by 90mm and have bolt in feet
------------------------------------
there are 4 complete blue panels, for all 4 sides
the buttons on the front could be for auto stop
-----------------------------------------

if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers
the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft

-------------------------------------------
theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis

-------------------------------------------

there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis

-------------------------------------------

there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.
these are fitted to 4 bits of 60 by 45mm -
THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.

there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius


----------------------------------------------
also there is stack and stacks of 45mm box, lots of nuts and bolts

all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.

------------------------------------------------

there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors

two of these
and two of these, the other one is a bit bigger all full of giblets

have all the wireing and connectors too.
---------------------------------------
there are two BUSHE pumps, rams, connectors and valves
-----------------------------------
location magnet things for 3 axis, 3 on each,
also have a trend t10 1/2 inch collet 2000kw plunge router, used for about 2 hours - ten years ago, in the case.
also have a 100a invertor / tig welder plasma cutter
i really should nail together a 4foot by 2 foot plasma table........

all used

IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR

I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.

NOW THE BEST BIT i NEED
Nema23 Stepper Motor Kit 3.1Nm x 3 Axis
ALSO NEED A SPINDLE AND MOUNT
AND SOME MACH3 - OR 4
OH AND A USB/lan BOB

SO HAPPY TO HAVE A SWAPSIES.
THANKS
erm, controlling stuff sold

NOW REQUIRE A SPINDLE AND MOUNT.
A USB BREAK OUT BOARD

HAVE NEW MOTORS
FOR SALE 2 ROUND NEMA 23'S 8 WIRE, AND A 6 WIRE SUARE ONE
ALSO 3 1/4 -TO - 1/4'' CONNECTORS

NEED SPINDLE AND MOUNT AND SOFTWARE.

COME ON!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
STEVE
0774 858 2044
LOADS OF 40MM BOX

YOU COULD MAKE A HALFF DOXEN TABLE YOPS