Wobblycogs CNC Mk2

[Wobblycogs]

I saw you mention you'd got a Csmio on another thread. I have to admit it had me interested but I couldn't find much else about it so went with the standard setup.

It certainly sounds like a top quality solution. If it's as good as you think and comes in at roughly the same sort of price I'll be more than happy to switch over, I await your review with bated breath :)

[JAZZCNC]

It certainly sounds like a top quality solution. If it's as good as you think and comes in at roughly the same sort of price I'll be more than happy to switch over, I await your review with bated breath :)

It's very high quality and looking brilliant so far. It will come in much cheaper than ESS/PMDX combo has you won't need the Pmdx126 or 107.

[Clive S]

Dean Will it slave the x motor. I thought only the S version did. But could be wrong. ..Clive

[JAZZCNC]

Dean Will it slave the x motor. I thought only the S version did. But could be wrong. ..Clive

Not got that far yet Clive but I think it does but just not within the unit with advanced features like -S model has and just leaves it down to Mach to control in normal way. Not sure how it will handle Homing etc but I'll try to test it out when get time.

For my use on intended machine then it's not required so I'm not concerned about that and has you know I try to avoid slaving anyway.

[Wobblycogs]

I'm must be missing some understanding because I've never seen anyone set up a machine in the way I'm about to suggest but I can't immediately see anything wrong with it...

Imagine a machine with dual x-axis steppers, why can't you just wire both stepper driver control lines in parallel to the x-axis connector on the BOB?

I can see that the signal strength (current) may be a problem as it will be halved but that doesn't feel like it would be insurmountable. If the machine is set up correctly wiring in parallel looks like the same end result as, for example, the slave feature of the PMDX-126.

Am I right in thinking that the step line indicates that the stepper should take a step by going high and then the direction line is high or low depending on the direction of rotation? Is there any other signalling taking place along these lines?

[Jonathan]

You could do it that way, but in Mach3 people like to home each X-axis motor separately to square the gantry, which clearly can't be done with them both connected to the same output. I'm not keen on that method as it bends the gantry, albeit only slightly, every time you home the axis.

Am I right in thinking that the step line indicates that the stepper should take a step by going high and then the direction line is high or low depending on the direction of rotation?

Yes, that's correct although it can be inverted.

[Wobblycogs]

Thanks Jonathan.

I can see that you couldn't home each motor separately with a parallel connection but I'm a little surprised that you would need or want to (at least after the initial machine set-up). Surely the two motors should be taking identical steps and therefore remain square on it's own?

Obviously no two steppers will be perfectly identical but the difference in step size between two motors must be tiny for the dual motor set up to work at all. Even if the two steppers did have a non-trivial difference in step size surely the worst case would be wherever is furthest from the home position getting worse in a linear fashion the further from the home position.

[Robin Hewitt]

Is there any other signalling taking place along these lines?

What pattern does the driver put on it's outputs when you switch on?

It may go to a set start position, it may go to the position it was at when you switched off.

You have to figure out if this can blow your start location.

[Wobblycogs]

What pattern does the driver put on it's outputs when you switch on?

It may go to a set start position, it may go to the position it was at when you switched off.

You have to figure out if this can blow your start location.

This is all hypothetical at the moment. I've been reading the manual for the CSMIO/IP-M which doesn't support slaving and I was wondering why I've not seen people just wiring drivers in parallel. I came to the conclusion there must be a good reason for it or BOB makers wouldn't advertise support for slaved drives as a selling point.