AM882 works with Protune - but not with the ZPA5-INT BOB

[JAZZCNC]

It says in the manual that erratic movement can be caused by weak signal or interference. How can I check for this?

You'll need an oscilloscope to do it properly but chances are you have just got something wrong with wires or settings.
Your not trying to run this with a Laptop are you.?
Where did you get the PP cable.? . . It must be a straight thru cable not an old printer or serial cable.

Regards the motor tuning then that's nothing to do with Drive settings it's the control software sending out pulse's and if you motor tuning is set to high you could be getting stalling motors.?

This will most likely turn out to be something simple like dodgy wire or wrong settings. Would be very unlikely you'll have electrical noise issues. The drives clearly work fine has do motors so they are ok and wired correct.

It could be PC related like low voltage parallel port, unfortunately don't know anything about your BOB so unsure if it pulls signals high or not.?

Sorry can't be more help than this.!!

EDIT: Oh if your using Mach3 then try the PP driver test to check your PP port.
If still having trouble and can't see any thing else wrong with wires, drives etc then sometimes a reinstall can help. It's not unknown for Mach's XML file to get corrupted and cause daft issues like this.!!

[badgerman]

Thanks Jazz - I will have a look.

[badgerman]

SO I messaged Gary and we talked over the issues, I noted that there was a brake on the stepper with 24v supply that might cause issue - she he said get rid of it and try again.

Removed the brake, ran the standard ZPA profile for mach and the stepper motor jittered so violently that it nearly jumped off the desk!! Not the 24v supply I am guessing. . . . .

I'm totally confused now so heres the rundown of trials to date -

It has worked with the pro tune and with the direct parallel connection ( I wired up a parallel to stepper driver cable and it worked a treat) so there can't be any issue from the stepper-drivers to the steppers, or in fact the computer outputting signals.

It has not worked in and out of the case, I initially tried it out of the case and thought the problem was as a result of it not being grounded properly. It did exactly the same when I put it in the case - so it can't be something isolated to its assembly and orientation in the case.

. . . . . So, I am going to put the Zpa unit in my other machine to see if somehow I have lunched it. I bloody hope I haven't because it was doing the same thing with both the ZPA boards I have - so I would have knackered both!!

Whatever is going on is happening on the ZPA board. I will wire up the board to my other machine tonight (GEKKO 203V's - worked a treat with them) but if it doesn't work I am seriously considering getting another board to try. Annoying though - £20 for the ZPA is a good price for a punt, but any more serious board will require more dollar. ... . . . and it still might not work!!!

Anyone got any suggestions for a cheap driver board that will do the job?

Chris

[JAZZCNC]

Anyone got any suggestions for a cheap driver board that will do the job?

That's were your going wrong.?? Bob's are one of the most trouble some components in the control box and buying cheap boards just increases your chances of trouble 10 fold.!! . . . If you think about it they handle all the signals and no matter how clean the signal when it reaches the board if the BOB has cheap nasty components then it will get degraded to some degree. Now send it usable signal but on the weaker side and cheap board can easily scramble it's brains out.!!

The only board I can recommend which you can buy in UK is this one. I've used many without problems, infact I'm installing one at this moment along with AM882 drives.
OPPB

[badgerman]

The only board I can recommend which you can buy in UK is this one. I've used many without problems, infact I'm installing one at this moment along with AM882 drives.
OPPB

Right, sounds like a plan. I was considering a better board as I have a VFD inverter and spindles I want to get running - I don't see any mention of spindle control on this board - is that the case?

[JAZZCNC]

- I don't see any mention of spindle control on this board - is that the case?

No it's a separate board if you want to control spindle speed.

You can use BOB's On board relays to control VFD start/stop signals. To be honest I don't often bother with spindle speed control and just control Start/stop.
I also use the relay built into VFD to control water pump so it's only running when spindle spinning.!

[badgerman]

No it's a separate board if you want to control spindle speed.

You can use BOB's On board relays to control VFD start/stop signals. To be honest I don't often bother with spindle speed control and just control Start/stop.
I also use the relay built into VFD to control water pump so it's only running when spindle spinning.!

Cool - I am not to sure I will need spindle control any time soon. I have 2 really nice spindles, one with a vortex tube on it pumping cool air down the centre of the cutter that I want to get running. The machine it came with had a KEB inverter that I need to start understanding . Spindle control won't be relevant until I have that sorted!!!

[badgerman]

The only board I can recommend which you can buy in UK is this one. I've used many without problems, infact I'm installing one at this moment along with AM882 drives.
OPPB

Just bought one of these bad boys.

Fingers crossed.

[badgerman]

Boom. Ordered a board from DiyCNC - out of stock. In comes Mr. Jazz to the rescue, sends me his spare (or next builds board). Realised it was out of stock thursday, Mr Jazz sends Friday, received on saturday and 90% wired on Sunday.

Board works a treat - I still don't know what was wrong with the ZP5A as it is working fine on my other machine (Gekko 203V) but this has dealt with the problem.

Thanks to all that waded in to help - particularly JAZZCNC you bloody legend.

[JAZZCNC]

Your Welcome, Cheap BOB's are just not worth the stress and hair loss. . Lol . . . Pleased your sorted and working.

PS: Money received thanks.!!