Spindle motor rewind

[johnsattuk]

[QUOTE=EddyCurrent;52560]I don't know exactly which motor you have but can you change the connections from star to delta ? it won't change the number of poles obviously but it would give a lot more torque. .[/Q

Changing star to delta connections will change the operating voltage and ~ double the amps required, doesn't change the torque curve of the motor.

More torque will require even more amps, which I haven't got, or more poles. This is in my garage on a 240v supply with my existing 3Kw VFD which is why I am looking at changing pole count.

[johnsattuk]

Update

I have eventually rewound my 2 pole spindle to 8 pole, dragged on a bit for a variety of reasons. Did a little research on rotor slot numbers, seems to be a bit of a black art with different motor manufactures doing their own thing, seems to be more to do with starting torque and efficiencies than any thing else.

Invested in a winding design service on the net, asked for 240v 400Hz delta connection, came up with 20 turns per slot.

Wound the stator at 20 turns two in hand 0.75mm wire, ~20A in delta no load running - ~12A in star, this was about 8 times the original motor.

Some emails back and forth getting me nowhere, seemed obvious to me that it was lack of turns (flux).

Decided to think it through on the basis that I knew the turns and current of the original motor and that HSD had got the ampere turns right.

Fortunately I had tried the motor before varnishing it so I was able to strip it down again very easily.

Wound the stator at 50 turns two in hand 0.55 wire, ~2.5A in delta no load running similar to the original motor, runs OK up to 500Hz which is more than I want.

From when I was a young lad my Father repeatedly told me ' Beware the Expert'

Not particularly neat but does the job OK

[Clive S]

Very interesting John, Just goes to show with knowledge and patience a lot can be achieved ..Clive

[GEOFFREY]

Brilliant, well done. I don,t suppose that you want to rewind my HF (1000hz, 55volt) to 400hz 230volt), for a (small) bag of gold of course. This is a serious enquiry as I too have been told that it is not possible. G.

[johnsattuk]

I don,t suppose that you want to rewind my HF (1000hz, 55volt) to 400hz 230volt), for a (small) bag of gold of course. This is a serious inquiry as I too have been told that it is not possible. G.

Sorry but modifying some one else's motor would be a bit scary , I persevered with mine mostly because I was told it's not possible and I could see no reason that it could not be done, just a matter of finding the correct info, I have spent a lifetime solving engineering problems, many of which were not possible.

There are motor design programs out there but they are very expensive, need to find a friendly face in one of the universities. I tried a couple of re-winders for info but they really don't want to know about anything non standard.

Modifying an existing motor should not be too difficult if you accept that the manufacturer got it right with respect to flux densities in the stator (ampere turns in old money).

This something I found somewhere on the net.

Rewinding for a change in voltage

If a 220 volt motor is to be rewound to operate on 440 volts, use twice as many turns on each coil and one-half the circular-mills area of wire. In other words, if 40 turns of NO. 17 wire were used on the original motor, 80 turns of NO. 20 should be used on the new motor

Some motors rated for 230 volts will not handle the load on 208 volts if loaded to the maximum. The turns must be reduced to the ratio of the voltage change. As an example, 230-volt motor has 40 turns: 230/208 = 1.1, 40 turns/1.1 = 36 turns. If there is enough room, the next larger wire size should be used. An easy way to determine whether there is enough room is to cut the required number of of lengths of wire of this size and fit then into the slot.

Changes for New frequency

There are two ways to convert these motors; one keeps the same horsepower for the new speed, and the other keeps the same torque for the new speed (more horsepower). For the same horsepower, use the following formula: old turns*Sqrt(old Hz / new Hz) = new turns. If you want the same torque then it is: old turns*old Hz/new Hz = new turns.

[Jonathan]

There are motor design programs out there but they are very expensive

Here's a free one:
https://www.emetor.com/
Although lately I've been using this one as it's on the university computers.

Anyway, Geoffrey, have you got a picture of the stator inside your motor? I'd be interested in rewinding it / working out how for you. Who told you that it wasn't possible and what reason did they give?

[johnsattuk]

Here's a free one:
https://www.emetor.com/
Although lately I've been using this one as it's on the university computers.

I did find and play with emetor and also Koil, and some demo versions of others, but really my only requirement was no of turns per slot and I did not find that these gave me that info.

I originally tried the forum in the hope that some kind soul would help with some positive info.

It is highly unlikely that I will wind another motor, this was a just a whim that became a challenge.

[GEOFFREY]

Here's a free one:
https://www.emetor.com/
Although lately I've been using this one as it's on the university computers.

Anyway, Geoffrey, have you got a picture of the stator inside your motor? I'd be interested in rewinding it / working out how for you. Who told you that it wasn't possible and what reason did they give?

Thanks for your reply and offer Jonathan. I do not have any pictures of the internals of my spindle as I have never thought about dismantling it. I have a couple of these spindles which I love to use because of the air release collet chuck and work around the fact that I am limited to 3.172mm shank tools. As I have a "spare" spindle I would be happy to take a chance that it does not work if you are prepared to try. The impossible comment came from various commercial rewinders and I had very little faith in that I believe that nothing is impossible!!! Perhaps a little difficult sometimes. The most logical comment came from one rewinder who said that it would be difficult on a small diameter spindle to use the heavier duty wire necessary to change. These spindles are lovely (ex pcb machine), but I only have one HF inverter and I would like to get one running on a standard 400hz inverter as I have started to strip down another machine which has a cutting area of 540x600mm. G.

I apologise if I seem to be hi-jacking this thread, but I did start a somewhat similar thread about my spindle and had no response. G.

[johnsattuk]

The most logical comment came from one rewinder who said that it would be difficult on a small diameter spindle to use the heavier duty wire necessary to change.

Not sure it was a very logical comment, I would expect the requirement would be for more turns of a smaller dia wire.

[Sourabhkumawat]

Can you share your email? I would like to do this modifications too. Just a couple of questions. 😅 My mail is [email protected]