Stepper driver voltages - using different levels

[Jonathan]

Which motors are you using?

You should be fine running the M542 drivers at 48V with a linear PSU, but I'd be inclined to get higher voltage drivers (e.g. DQ860MA) and run them at about 70V as the difference in price shouldn't be that great. The current ratings of the higher voltage drivers will be greater, so they should last a long time as they wont heat up much.

From an electrical point of view there's nothing wrong with mixing drivers of different voltages, so long as they are each supplied with the correct voltage which you plan to do, so nothing to worry about.

[routercnc]

Hi Jonathan

Thanks for that. I have a big spreadsheet of my configuration - here is a cut and paste of the motor data:

Axis Model Configuration V A Nm mH
X1 M60STH88-3008DF Bipolar Series 5.46 2.1 3 12.8
X2 M60STH88-3008DF Bipolar Series 5.46 2.1 3 12.8
Y* SY60STH86-3008BF Bipolar Series 5.46 2.1 3 12.8
Z** ? Bipolar parallel 1.8

* this is the new motor but to keep the X axis motors the same the old Y motor will go on the X2 axis.
** can't remember why I bought the Z axis motor at 1.8Nm but it's been working fine for years.

I'll look into the higher voltage drivers and weigh it all up . . . .

[JAZZCNC]

Don't think about it just do it.!! . . . . .Buy 80Vdc drives and Run the motors Bi-polar parallel with 65-70Vdc and the differance will be night and day.!!

Just having proper drives running decent volts instead of the tin pot System4 setup will make a big enough differance. The above will transform into a real machine.!

[Jonathan]

Yep .. with those 3Nm motors the ideal voltage is 70V. Buy the 80V rated drivers and you certainly wont regret it. However, do check that the inductance of the Z-axis motor isn't significantly lower than the other motors as if that's the case it may overheat on 70V, in which case you would have to run it wired in bipolar series, but it'll still be far better than the current system.

Edit: Forgot to mention in the first post - cutting aluminium is no reason to upgrade the motor drivers. If you use single flute tools you'll be cutting at 600mm/min, so no doubt well within what the machine can currently manage. Clearly higher feedrates are required with more flutes, but still much less than that of cutting wood.

[routercnc]

Hi Jonathan,

Thanks for the Z axis motor info. It has been many years since I looked at the data for the Z axis motor so I will check it when the time comes and follow your advice accordingly.

I hear what you are saying about cutting aluminium and the feedrates / driver requirements, and that in itself it does not justify an upgrade. My experience has been that cutting aluminium on the MK2 machine (which is about to be replaced with my MK3 machine, details to follow) was a bit hit and miss with aluminium sticking to the tool and lots of vibration etc due to the wooden gantry sides (!) and unsupported wooden bed (!). The new machine should be so much better structurally that I felt that to make best use of it overall I wanted to match it with better drivers and that was really driving my questions.

[routercnc]

There seem to be alot of sellers listing the MA860H drivers such as below:

CNC Kit CNC Breakout Board +Cables+ 3 Axis MA860H Stepper Driver Controller 7.2A | eBay

How would you rate these compared to the DQ860MA mentioned in post #2?

I know you like to make you own linear supplies, but I would prefer to go for another ready made switched mode such as:
CNC Power Supply 350W 60V 6A For CNC Stepper Motor Driver MA860H M542H NEMA34 | eBay
Any views on that one?

Thanks for your help.

[Jonathan]

The MA860H looks to be the same as the DQ860MA, except rated for 80VAC instead of 80VDC ... which is quite a big difference. It implies you could just get a toroidal transformer with a 50VAC (or 2*25V etc) secondary winding and connect it to the drivers, which is quite convenient.

However they are quite a lot more expensive than the DQ860MA - have you checked on AliExpress.com - Online Shopping for Electronics, Fashion, Home & Garden, Toys & Sports, Automobiles from China. You can also e-mail wantai-motor directly and they'll probably give you a good price. They did for me at least.

Why do you prefer to go for the SMPS? It's a much more expensive option.

[routercnc]

The specs say that the MA860H will take both 80VAC and 110V DC, which is probably why it is more expensive.

I'll check out AliExpress and add DQ860MA to my list of possibles.

I don't touch mains projects and am quite happy to pay extra for a ready made SMPS.

Thanks