Which Type of Limit Switch

[EddyCurrent]

These are the ones I used;
http://www.ebay.co.uk/itm/2pcs-SN04-...item5d38dcb5f5
Albeit on a router, they work well and are very repeatable. Because they are 3 wire NPN you can power them from a 24v supply but still connect the output to your 5v bob input where they either leave it open (high) or short it to ground (low).
The drawing here shows how they are connected; (bottom left corner of drawing)
http://www.mycncuk.com/threads/6565-...7622#post57622

[Clive S]

Eddy beat me to it but there are these as well and bit cheaper. I use this sort of thing on my router and will be fitting them to the mill. You do have to watch out for swarfe but if they are mounted under the bed or have a cover over I don't see a problem.

Normally open http://www.ebay.co.uk/itm/TL-Q5MC2-I...item1c41faa863 or

http://www.ebay.co.uk/itm/New-LJ12A3...item53ffd022e5

Normally closed:- http://www.ebay.co.uk/itm/DC-6-36V-N...item417755e4ae and

http://www.ebay.co.uk/itm/4mm-Tubula...item43bbcedff7 Also
this :- http://www.ebay.co.uk/itm/DC-10-30V-...item43bbcddc3b ..Clive

[manofgresley]

Many thanks, I like the look of this one,http://www.ebay.co.uk/itm/New-LJ12A3...item53ffd022e5 i can easily fit these to my machine, my Bob is only 5 volt so do i need a relay? and how do i wire a 3 wire switch, can you do me a schematic, i'm not an electrician.

RayQUOTE=Clive S;60092]Eddy beat me to it but there are these as well and bit cheaper. I use this sort of thing on my router and will be fitting them to the mill. You do have to watch out for swarfe but if they are mounted under the bed or have a cover over I don't see a problem.

Normally open http://www.ebay.co.uk/itm/TL-Q5MC2-I...item1c41faa863 or

http://www.ebay.co.uk/itm/New-LJ12A3...item53ffd022e5

Normally closed:- http://www.ebay.co.uk/itm/DC-6-36V-N...item417755e4ae and

http://www.ebay.co.uk/itm/4mm-Tubula...item43bbcedff7 Also
this :- http://www.ebay.co.uk/itm/DC-10-30V-...item43bbcddc3b ..Clive[/QUOTE]

[irving2008]

Wiring of these was discussed at length on many threads. Here is a schematic I did for one such thread showing all possible variants...
You don't need a relay, its overkill and unnecessary if your BOB has opto-isolated inputs.
.

[manofgresley]

Hi Irving, I did say i am not an electrician, how do i know if my Bob is opto isolated i have the paperwork for it but there is no mention of this? Which do i need, NPN or PNP, i'm confused.

Regards

Ray
.

[/QUOTE]

[manofgresley]

These are the ones I used;
http://www.ebay.co.uk/itm/2pcs-SN04-...item5d38dcb5f5
Albeit on a router, they work well and are very repeatable. Because they are 3 wire NPN you can power them from a 24v supply but still connect the output to your 5v bob input where they either leave it open (high) or short it to ground (low).
The drawing here shows how they are connected; (bottom left corner of drawing)
http://www.mycncuk.com/threads/6565-...7622#post57622

I only have a 5 volt supply will this work?

Ray

[Clive S]

I only have a 5 volt supply will this work?

Ray

You really need a 12V or 24V power supply to work but they can still be connected to your BOB, power supplies are not expensive. ..Clive

[manofgresley]

You really need a 12V or 24V power supply to work but they can still be connected to your BOB, power supplies are not expensive. ..Clive

I do have both power supplies in my CNC cabinet, so can i refresh -
I need 12 to 24 vdc proximity switches, NPN, N.C. all i need know is a scheme / Wiring diagram, can you help?

Ray

[EddyCurrent]

This is the drawing. You will have to make sure the 0v terminals of both power supplies are connected together otherwise it will not work. Where it shows a 24v dc PSU you could use a 12V dc PSU instead if desired.
Colours of the proximity switch wires are for the ones I used but I think they are pretty standard.
Because these are home switches I was not overly concerned about N/O, N/C, so for example mine are 'off' and 'open' until they are activated whereupon they are 'on' and 'closed'. If you get yours wired up and they operate the wrong way you thought they would you can just 'invert' their operation in the software.

[manofgresley]

Hi Eddy. I'm confused, why do i need a separate 5 volt psu, when my BoB is already putting out 5 volt. On the board there are terminals for 5 limits but only two wire each, + & -, Am i reading it wrong or what?

Ray

This is the drawing. You will have to make sure the 0v terminals of both power supplies are connected together otherwise it will not work. Where it shows a 24v dc PSU you could use a 12V dc PSU instead if desired.
Colours of the proximity switch wires are for the ones I used but I think they are pretty standard.
Because these are home switches I was not overly concerned about N/O, N/C, so for example mine are 'off' and 'open' until they are activated whereupon they are 'on' and 'closed'. If you get yours wired up and they operate the wrong way you thought they would you can just 'invert' their operation in the software.