my 6040 experience (yeah, and problems) so far

[jimbo_cnc]

So I've established that D2 faults even when by itself. D1 and D3 do not fault.

When I use D1 and D3 together, D1 faults (whether it is X or Y axis). Go to about 2:40 to see the problem demonstrated.
http://youtu.be/raNVEsXro5c

I did a prolonged test with the strongest driver D3 on the long axis, almost no graunching noise after 10mins (, except at 9:21 !) video: http://youtu.be/3EQlJWFV8XY

I've now tested some GCODE, same fault. eg zigzg lines don't work on one diagonal.


My 1flute cutters arrived so I had to make my first cut in delrin, 11000rpm DOC 1mm feed 1100mm/min. It was quite loud, the delrin was in a vice clamped to the table. It's all a bit like an aluminium drum at the moment, I will have to add a layer of something once I've thought about how I'm going to clamp my work etc

[amxen]

Hi iv just picked up a 60/40 just the same as yours but it has the all in one board. Iv had problems with my motors as well. if i set the tuning to what they say in the set up sheet, Then run them at 100 jog they jam when i running them up and down. they run for about 50mm then jam. I have set the motor tuning to half what they say and they seem to run ok. so that would be 400 1000 100 . Iy runs slower but no horrible crunching. This is my first cnc so i dont know enuf to know if this is ok but its running.

[EddyCurrent]

Must be age related but I've been getting mixed up with this thread http://www.mycncuk.com/threads/7816-...0874#post60874
As amxen says get the velocity and acceleration down on Mach3 to something that won't (shouldn't ?)cause any issues.
Once that's eliminated my stab is that the breakout board is faulty and it's either a bad soldered joint on the inputs pull-up resistor pack or the pack itself. (sometimes I like to live dangerous )

[jimbo_cnc]

The good driver is happy running the long axis at 4000mm/min & 400mm/s2 (twice the standard) on its own. The fault occurs even with all axes at 1/2 standard speed.

What's a half decent PSU/BOB/3x drives gonna cost me? If the seller can't replace quickly or the next ione is also faulty I'll be after a discount towards my replacement controller box.

[EddyCurrent]

I may be wrong but I think these are the main UK suppliers of stuff used by DIY'ers, plus obviously there's ebay.

http://www.diycnc.co.uk/
http://www.zappautomation.co.uk/
http://cnc4you.co.uk/

If I was in your position I woud change the breakout board first and would most likely choose a similar board from ebay, they are less than a tenner from abroad, in fact I have just realised I have a board like yours that I bought to get extra inputs to my system, it's working fine in that role. It connects into port2 of my SmoothStepper

[JAZZCNC]

I would go for the part refund and buy decent electronics with a mind to transplant to your next machine. . . . No point replacing crap with crap.!!

To be honest I'd want more than just the refund of the Drive and BOB there's your fiddling time and Down time to take into acount.
These things need to be accounted for when your thinking about electronics and machine because what's the point having a machine if your spending more time chasing faults or fixing the bloody thing or than using it.?

[amxen]

just found out what my problem is. made my own post

http://www.mycncuk.com/threads/7839-...1165#post61165

dont know if it will help any one