-
19-10-2014 #21
No worries Eddy, and thanks everybody especially John. The circuit looks easy enough, I should be able to test it sometimes next week.
Alternatively, I have found an off the shelf converter from Axiomatic:
http://www.axiomatic.com/TDAX13020X.pdf
But I have a feeling it's going to be much more expensive than the diy version John proposed, so not really an option.
On another note, can somebody confirm a 24-28v 10A power supply would do, and what voltage do you feed to stepper drivers?
-
19-10-2014 #22
Hello Miller,
Let me know if it works and any questions.
On the PSU, the one I use in my Novamill conversion is similar to the 36V one here: but I got mine direct from China via ebay for rather less money IIRC. Look for topengineer1989 as the seller. I use the common 2M542 drivers. 36 volts is fine to drive the steppers assuming the drivers are rated up to 40 or 50 volts. I think I have set the X and Y currents to just less than 2A and the Z probably 3 but could check those.
John.
-
19-10-2014 #23
Yes, that's the seller I bought the BOB from. It came as a complete package with 3 x 2M542 drivers. Still in the post but should be getting it quite soon.
The motors are rated 1.5A and 3A at 30V, so I will keep about same amp rating and feed 36V then.
What I had in mind for power supply is this. It shouldn't make more than £30 posted and looks nice quality and DIN mounted, but if it's less than ideal because of the lower voltage, I'll go for the 36V as you suggested.
Just to confirm, your circuit has 2 x 470K and 3 x 47K resistor. I have selected this for C1, and this for C2, and this for the op amp.Last edited by Miller; 19-10-2014 at 03:48 PM.
-
19-10-2014 #24
I had to get up at 4:30 am this morning to get rid of my duff drawing, couldn't sleep knowing it was there
John, it looks to me like the input to the drive is terminal 3, terminal 2 goes to a pot for 'minimum speed' which creates a potential divider along with the external pot to give an offset from zero.Last edited by EddyCurrent; 19-10-2014 at 03:44 PM.
Spelling mistakes are not intentional, I only seem to see them some time after I've posted
-
19-10-2014 #25
Oops! Eddycurrent, you're quite right, terminal 3. Terminal 2 is not connected.
Miller, the eletrolytic you selected is a surface mount type, is that what you wanted? The other one is leaded. Maplin is a good place for miscellaneous components. Well, the 36 V works fine for me, lower voltages may work but the drives are fine with 36. That's the package I bought too of the BoB and drivers.
John.
-
19-10-2014 #26
-
19-10-2014 #27
This is a good place for components too;
http://www.rapidonline.com/Electroni...tic-CapacitorsSpelling mistakes are not intentional, I only seem to see them some time after I've posted
-
19-10-2014 #28
The voltage rating isn't critical, 16 V is fine, leaded much easier to solder.
-
25-06-2015 #29
I gather that this circuit has now been built and works which is nice to know!
Thread Information
Users Browsing this Thread
There are currently 2 users browsing this thread. (0 members and 2 guests)
Similar Threads
-
FOR SALE: for sale: Denford Novamill
By Mash Govan in forum Items For SaleReplies: 4Last Post: 12-04-2016, 11:18 AM -
eBay: Denford Triac with Mach3 Conversion
By large519 in forum Items On eBay UKReplies: 0Last Post: 29-04-2015, 05:34 PM -
CONVERSION: Denford Triac Mach3 conversion
By rnr107 in forum Conversion Build LogsReplies: 11Last Post: 23-10-2014, 02:44 PM -
FOR SALE: Novamill, converted for Mach3 for sale.
By Mad Gnome in forum Items For SaleReplies: 9Last Post: 09-10-2014, 03:23 AM -
RFQ: Looking for somone to finish conversion Denford Mirac with Mach3
By CHudson in forum Projects, Jobs & RequestsReplies: 0Last Post: 14-10-2010, 08:20 PM
Bookmarks