First CNC build - VFD wiring question

**Neale** · 15-02-2015

I think that Eddy has already pointed out that the inverter manual takes into account over-current. Not sure what that inverter is rated at, but I use a 5KW inverter on my lathe which is rated at something like a few seconds at 100% overload and 30 sec at 50% overload. I think that this is probably to allow for motor run-up initial surge, although I'm not driving it that hard. However, let's say max load for a normal Chinese VFD/spindle combination is a nominal 2.2KW, and allowing for conversion inefficiency, that's going to draw maybe 2.5KW from the supply. That's about 10A. Short-term permitted overload is about twice that, which neatly comes out to about 20A - which is where we started!

In real life, though, I would suggest that there are two possible times when the inverter is likely to trip the supply fuse/breaker. One is when you first switch it on. These devices typically rectify the incoming single-phase supply to give a DC supply internally which then drives the 3-phase output generator. There will be a small surge at that time which can give problems. Sometimes the problem is due to funny phase relationships between input current and voltage which can trip RCDs. However, my limited experience with my 2.2KW inverter is that this never happens (although it is a problem for the big inverter I use). Second time it might trip is when the load comes on, i.e. motor startup. However, the inverter is generally set to soft-start the motor - ramp up speed over a few seconds - and that keeps the peak load down. Anyway, you will be spinning up a motor when it is not cutting, so that reduces the load as well.

Upshot of all this in practical terms - it works fine for typical router purposes off a standard 13A socket!

**Bez** · 15-02-2015

Cheers for the replies guys :)

Looking through the manual it states its output current at 10A. Its not a fancy VFD just a huflugdung (Huanyeng) special bought from here http://www.cnc4you.co.uk/Spindle/Spi...h-Matching-VFD.

13A plug sounds like a winner to me but I will obviously be careful with other items running on the same ring until I can figure out its own ring for it to sit on.

So looking under the front panel I'm faced with this:

Motor wires are self explanatory so no need to go over those. Where I'm a bit confused is R S T ...... does it matter which one the live and neutral go to? Obviously the earth goes to "9"

I'm using a KK01 breakout board which has a relay output ..... am I correct in thinking this can be used to start and stop the spindle. If so which would be the correct blocks to wire it into from the basic mention in the manual DCM looks like it might be the one but rather than mess things up I'd appreciate any input for people who have run or are running a similar setup.

Thanks again.

**Neale** · 15-02-2015

Mains input is easy - just use two out of RST, and it doesn't matter which one is live and which is neutral.
Can't help off-hand with the spindle switching as I don't use it at the moment. One day I'll get round to proper spindle speed and on/off control, but I'm not there yet! For the time being, I just use the front panel controls.

**Dwayne Dibbley** · 15-02-2015

Here's what came with mine, should be of some help...

**Bez** · 15-02-2015

Nice one :) I like pictures like that ....... its like painting by numbers lol

**Bez** · 16-02-2015

Thanks for your help guys its all up and running now :)

**rbs** · 05-03-2015

Hi guys,

I just bought the KKO1 BOB, I'm trying to to hook it up to the DIYCNC spindle board and then onto the VFD so i can have Mach 3 Control. I would also like to use the spare relay from the KK01 for on/off of a vacuum table lets say. Is any one able to confirm the wiring it correct. I really don't want to blow up any more components. the two links below are for the manuals. many thanks

pic host

https://www.mediafire.com/?rc61wkf8r4m4or6

https://www.mediafire.com/?rc61wkf8r4m4or6