Thread: Spindle 2?
-
15-06-2009 #21
Decent bargain, they are good inverters, not really any bad modern ones about.
Mitsubishi's can be a pig in that they often sell the programming panel and filters seperate so it adds up to ££££.
You should have no problem with this one.
.John S -
-
15-06-2009 #22
Phew, thats a relief, I didnt even google the manufacturer (not like me), saw it and had to go out, so put £50 on it just in case.
What would be a safe motor rating to use with it? Or will the instructions tell me...
-
15-06-2009 #23
Technically anything up to 1 HP but most can be programmed for 150% overload safely so it will run a 1 1/2 HP but may trip under hard load.
I have one of the 1 1/2Hp Chinese spindles here running off a 0.55Kw [ 3/4HP ] IMO Cub inverter, the cheap one, programmed for 150% overload and it runs fine with up to 6mm cutter in it.
Been running test cycles with this for about 4 hours, non stop at 24,000 rpm and no problem although it is a bit small and I wouldn't recommend it for continuous use or any larger cutter.John S -
-
16-06-2009 #24I have one of the 1 1/2Hp Chinese spindles here running off a 0.55Kw [ 3/4HP ] IMO Cub inverter, the cheap one, programmed for 150% overload and it runs fine with up to 6mm cutter in it.
Been running test cycles with this for about 4 hours, non stop at 24,000 rpm and no problem although it is a bit small and I wouldn't recommend it for continuous use or any larger cutter.
-
17-06-2009 #25
Kip,
You only need to get the stator wound, the rotor is just an alloy and iron lamination.
You can even get standard motors rewound from 2 pole 3,000 rpm at 50 hz to 12,000 rpm at 200 hz without then going pear shaped.
You need to work on the spindle as regards tool holding etc and front bearings but it can be done.
Just a teaser
.John S -
-
17-06-2009 #26I wouldn't know a piece of Maple if you hit me with it
Kip,
You only need to get the stator wound, the rotor is just an alloy and iron lamination.
You can even get standard motors rewound from 2 pole 3,000 rpm at 50 hz to 12,000 rpm at 200 hz without then going pear shaped.
You need to work on the spindle as regards tool holding etc and front bearings but it can be done.
Just a teaser
No problem with bearings and tool holder as I'm going to use dedicated spindle with ER32 collet chuck and then just use different motors to drive it
-
17-06-2009 #27Oi I'll start taking the piss.... :naughty:
breaks the monotomy of dullards like me asking stupid questions all the time
-
25-06-2009 #28
Picked up a 3ph motor today, have been told it works but want to know if there is a way to test the motor before powering it up and possibly damaging the vfd.
The motor is 0.75kw, 2800rpm and 230v if wired in star config.
Cheers in advance
-
26-06-2009 #29
You wont damage the VFD, it'll just trip out. Just set it for a low speed before hitting run...
I just picked up a IMO Cub CDS 0.75kW inverter ( for £35! I'm sure the guy had put it on wrong, £30 initial price £35 Buy It Now... so I did! Found the manual on the net too...
So now I can run the lathe and mill independently...
-
15-02-2011 #30
I'd also recommend Yaskawa & FUJI. I wouldn't recommend ABB to anybody.
Has anybody worked with Yaskawa's latest drive?
http://www.clrwtr.com/Yaskawa-A1000-Drives.htm
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Chinese 300W DC spindle - is the spindle shaft grounded?
By HankMcSpank in forum Spindles & Drive MotorsReplies: 44Last Post: 26-11-2016, 07:25 PM -
CNC Spindle Repair and Spindle Replacement for any Machine of any Manufacturer
By spindeldoctor in forum Manufacturer NewsReplies: 0Last Post: 13-11-2013, 07:50 PM -
Spindle lock mechanism for 2.2kW china spindle
By Jonathan in forum Generic Chinese SpindlesReplies: 8Last Post: 13-08-2012, 08:39 PM -
WANTED: Spindle holder for 1.5kw Chinese spindle.
By jcb121 in forum Items WantedReplies: 19Last Post: 14-10-2011, 02:07 PM -
DIY Spindle - What type of bearings are best suited for a spindle.
By 8iggles in forum Spindles & Drive MotorsReplies: 18Last Post: 09-02-2011, 10:15 PM
Bookmarks