One ring to rule them all?

[njhussey]

Yes, that's what I meant

[Rufe0]

Just easier to draw it hanging out the front so you can see where it is

[Robin Hewitt]

I may have misread this but the two rails under the bed seem to give total support to the outside edges and none in the centre? As most of the cutting will actually tend towards the centre do you think this is a good idea?
I have never quite figured out the optimum separation but there must be one

[Rufe0]

I may have misread this but the two rails under the bed seem to give total support to the outside edges and none in the centre? As most of the cutting will actually tend towards the centre do you think this is a good idea?
I have never quite figured out the optimum separation but there must be one

Mmm as pictured the bed would be made of 100x100 square hollow section so shouldn't flex too much. However liear rail is cheap so wouldn't hurt to add one in the middle.


Just doing the numbers, using 100x100x5 shs @ 14.7kg per meter. The traveling 0 shape fixed but moving gantry design reqires 4.2m of tube per 100mm width. So for a 200mm wide traveling 0 it would weigh 120kg, heavy but just managable .


The very tall normal machine of the same size would need 15m of tube which would weigh 220kg.

[Robin Hewitt]

Flex is not the real issue, right now the name of the game is minimising the overhangs -smileyface

[Rufe0]

Had another idea and amazingly I found a CAD program I actually like, it's a miracle! It's not for everyone in fact it's probably some people' worst nightmare but it's right up my ally. Instead of using your mouse to click where you want something you type it out in a sort of programming language.
http://www.openscad.org/

This design is sort of in between a fixed and moving gantry. As a result the bed is lighter than a moving gantry design and the gantry is lighter than a fixed gantry design. What do you think?

If your interested in this cad program you can recreate my drawing with this code

color("Azure") cube([900,1500,100]);//bed
translate([38.5,0,100])color("grey") cube([22,1500,23]);//left bed rail
translate([838.5,0,100])color("grey") cube([22,1500,23]);//right bed rail
//
translate([30,310,105.5])color("green") cube([40,80,34.5]);//left front Ccarrige
translate([830,310,105.5])color("green") cube([40,80,34.5]);//right front Ccarrige
translate([30,710,105.5])color("green") cube([40,80,34.5]);//left rear Ccarrige
translate([830,710,105.5])color("green") cube([40,80,34.5]);//right rear Ccarrige
//
translate([0,300,140])color("WhiteSmoke") cube([100,100,1000]);//left front upright
translate([800,300,140])color("WhiteSmoke") cube([100,100,1000]);//right front upright
translate([0,700,140])color("WhiteSmoke") cube([100,100,1000]);//left rear upright
translate([800,700,140])color("WhiteSmoke") cube([100,100,1000]);//right rear upright
translate([0,400,140])color("WhiteSmoke") cube([100,300,100]);//bottom left front-back join
translate([800,400,140])color("WhiteSmoke") cube([100,300,100]);//bottom right fb join
translate([0,400,1040])color("WhiteSmoke") cube([100,300,100]);//top left fb join
translate([800,400,1040])color("WhiteSmoke") cube([100,300,100]);//top right f join
translate([100,300,1040])color("WhiteSmoke") cube([700,100,100]);//front left-right join
translate([100,700,1040])color("WhiteSmoke") cube([700,100,100]);//back left-right join
//
translate([38.5,278,140])color("grey") cube([22,23,1000]);//front left Cgantry rail
translate([838.5,278,140])color("grey") cube([22,23,1000]);//front right Cgantry rail
//
translate([30,260,410])color("green") cube([40,34.5,80]);//left front gantry carrige
translate([830,260,410])color("green") cube([40,34.5,80]);//right front gantry carrige
//
translate([38.5,800,140])color("grey") cube([22,23,1000]);//rear left Cgantry rail
translate([838.5,800,140])color("grey") cube([22,23,1000]);//rear right Cgantry rail
//
translate([30,805.5,410])color("green") cube([40,34.5,80]);//left rear  carrige
translate([830,805.5,410])color("green") cube([40,34.5,80]);//right rear carrige
//
translate([000,160,400])color("Seashell") cube([900,100,100]);//front gantry
translate([000,840,400])color("Seashell") cube([900,100,100]);//rear gantry
//
translate([0,198.5,500])color("grey") cube([900,22,23]);//front gantry rail
translate([0,878.5,500])color("grey") cube([900,22,23]);//rear gantry rail
//
translate([310,190,505.5])color("green") cube([80,40,34.5]);//left front Ccarrige
translate([610,190,505.5])color("green") cube([80,40,34.5]);//right front Ccarrige
translate([310,870,505.5])color("green") cube([80,40,34.5]);//left rear Ccarrige
translate([610,870,505.5])color("green") cube([80,40,34.5]);//right rear Ccarrige
//
translate([300,160,540])color("Honeydew") cube([400,100,100]);//front spindle
translate([300,840,540])color("Honeydew") cube([400,100,100]);//rear spindle
translate([300,260,540])color("Honeydew") cube([100,600,100]);//left spindle
translate([600,260,540])color("Honeydew") cube([100,600,100]);//right spindle

[Clive S]

Had another idea and amazingly I found a CAD program I actually like, it's a miracle! It's not for everyone in fact it's probably some people' worst nightmare but it's right up my ally. Instead of using your mouse to click where you want something you type it out in a sort of programming language.
http://www.openscad.org/

I used to use openscad a few years ago for 3D printing I think then it only produced stl files also it wouldn't import much into it or output dxf etc.