-
02-12-2018 #1
So.. after much trolling this and other cnc websites, youtube and all the other stuff you end up looking at whilst researching, I finaly ordered up some AC servos, a VFD and a CS Labs CSMIO IP/A with I/O expansion and MPG module.
Being that this lot cost a fair lump of cash, I want to be VERY carefull in getring the wiring correct.
I get the majority of the connections, but wanted to make sure that all was correct before I started.
I emailed CS labs for help, asking if they could do a quick connection diagram for a servo drive and for VFD ( literature supplied), as none on the diagrams on their web site, fully matched up with the drives I have.
( is it just me, or does an ISO standard for terminal identification not exist yet for drives)
The response was far less than I would have expected, for a company pitching their goods at industrial users.
It was basicly " busy, may be able to help in about 8 weeks".
What!!
A.C. Servo drives are AASD-20A
( CONTROL VIA -10V~+10V)
VFD is a chinese 9100 series 2.2KW
( speed control 0-10V +fwd, rev, stop)
Anyone got experience of wiring these in to an IP/A?Last edited by swarf-boy; 03-12-2018 at 01:03 PM.
-
03-12-2018 #2
Ye, they *might* make good kit but never really been impressed with them post sale.
I can show you how to wire the stuff, not too difficult. Is that the driver manual / image of the connections page?
-
03-12-2018 #3
-
03-12-2018 #4
Hi Chaz,
Yes that's what I was able to attach.
I have also just attached an xcel spreadsheet I did, showing everthing I have worked out so far.
( probably a bit unconventional, but it seamed a simple way to plan it)
Feel free to mark my homework...... LOL.
Comments welcome from all.Last edited by swarf-boy; 03-12-2018 at 01:08 PM.
-
03-12-2018 #5
-
03-12-2018 #6
-
03-12-2018 #7
.
Last edited by swarf-boy; 03-12-2018 at 01:13 PM.
-
03-12-2018 #8
Pm sent mate
-
06-12-2018 #9
wont your new drives run position mode? step/direction?
would make it much easier to set up and would have saved getting the csmio.
i can help you with the ecogoo .
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Upgrade questions fro beaver mill VBRP Mk2 with Anilam Crusader II controls
By Breg90 in forum Milling Machines, Builds & ConversionsReplies: 11Last Post: 25-05-2020, 08:08 PM -
Upgrade to x axis required. MG or HG rail
By marbles in forum Rails, Guideways & BearingsReplies: 0Last Post: 10-12-2017, 01:51 PM -
CONVERSION: Novamill mach conversion upgrade
By Benja in forum Conversion Build LogsReplies: 4Last Post: 18-09-2017, 09:23 AM -
Emco pc mill 55 upgrade
By Craiggillzzr1400zx10r in forum Emco Milling MachinesReplies: 30Last Post: 31-08-2016, 03:13 AM -
picture conversion to DFX/ Gcode. Help required please.
By Gasgasbones in forum Programmers CornerReplies: 17Last Post: 19-12-2014, 11:42 AM
Bookmarks