- VFD Question
- G540 - 4 motor connection problem
- op-amp to drive +/-10V analog servo from old +/-5V controller
- Missing Steps Poss TB6600 Fault
- Current favourite stepper drivers
- The 2DM860H chinese controllers vs the rest?
- 6 wire motor options
- Roy's DIYCNC System 3 board
- Output voltage from mains driver?
- Mini Mill Conversion - best stepper drive choice
- Lenze i500 Inverter
- Stepper driver recommendations
- Wantai stepper drivers
- Step/Dir vs Pul/Dir
- Geckodrive G251X / G201X or Leadshine AM822?
- huanyang vfd is it worth repairing
- Leadshine AM822 drivers purchased!
- MK4 MACH3 Motion Card Problem with output control ports. NEED HELP!
- TB6600 / HY-DIV268N-5A Problems, and possible solutions
- Cnc router spindle wanted.
- em806 Senssorless Stall Protection fault
- Speed control option for a dc motor that is not part of a CNC, and eBay controller.
- Recommended breakout boards?
- Uccnc hdbb2 wiring help needed
- 12v --> 10v Nowforever D100S2R2B inverter & MKS-V-V02 CDXHCTECH board
- Need some help finding info on these motors please HY200 2226 0470 ACM8
- Best Drive for Fanuc AC servos
- Granite devices IONI
- DMM Servos
- Newbie stepper kit
- HSS86 and 2HSS86H Closed Loop Drivers
- which wire for stepper driver to socket on control box
- Looking for input
- Any USB/Ethernet controller suggestions?
- What software would be recommend?
- Why Ethernet instead of USB?
- Syil Stepper driverS pd2064ma002
- Tb6600?
- Which stepper driver is a good alternative to Gecho 540
- Help please. Dip switches and mach 3 settings
- Optimal voltage...
- BOB suitable for 3 axis+ B/C head build?
- Servo motor and inverter dilemma
- Buck Boost Transformer 380V 240V 3Phase
- Has anyone ordered directly from www.jmc-motor.com?
- Nema34 - DM860A Driver & Mach3
- 3DM860 driver question
- Pro Ma PPM 0322 CNC mill
- z axis probe connection
- Spindle control via PWM, Linux CNC on DC motor
- Huangyang gt series Vector control vfd ? Whats the difference?
- Nema 34 upgrade issues
- EMC/EMI filter question
- DIR+/- and PUL+/- motor, but single STEP and DIR signals
- geco drive G540
- Anything about the Dm542t or Dm542a???
- Replacing an encoder on vmc 3020
- Does it matter?
- Quick addition of 2.2kw spindle with VFD - Is this possible?
- Understanding motor frame sizes
- Re digital drives
- How Strict is the Max Vsupply Calculation for Steppers?
- Suitable stepper motor drivers for my creation
- Huanyang HY01D523B inverter settings.
- Controlling the motor (spindle) with Mach3
- Closed loop stepper motor kit power supply
- Replacing a Digiplan SD/3 with something else, help please
- Manual Control of Z Axis
- MACH 3 Soft Limit effecting A Axis Rotary
- Rampant inflation!
- Inverter and 3Ph Motor - Very slow revs
- Looking for someone who can upgrade my 3 axis controller in Berkshire
- AXBB-E any opinions?
- Lathe Reverse
- TB6600 4 axis board - GPIO input?
- Positioning three phase induction motors.
- Yaskawa Servopack power connectors?
- Flashing led. DM860A
- Yaskawa Servopack - stuck in baseblock - any ideas?
- Erratic stepper motors
- EM806 overvoltage
- PSU design
- What driver for vexta stepper query
- Single phase input variable frequency inverters XSY-AT1
- L293D used to reverse motor direction 7.8 vdc
- 110v 3 phase for baruffaldi turret
- 4th axis closed loop stepper/driver setup query
- Searching for a replacement for stepper motor driver
- ddcsv2.1 controller
- Sumtor Control Board - homing/limit switches
- Advice on Controller Board upgrade for CNC 6040
- CNC 6040 Controller Board Upgrades
- Xsy-at1 connection translation
- Gecko G540 Red Led Issue
- Strange problem
- bonmet servofly
- enable pins on stepper driver
- 240V VFD to power 110V motor
- New Build, New problems, need help.
- Run a stepper from 2 DM542 drive
- Panasonic MSD043Axxx Servo Driver pin outs????
- Baldor Flex Drive Serial Communication
- DIP switch setting
- Searching for source for 4-axis TB6600 controller board
- Cncest router dual mode mach3 and grbl
- Lichuan LCDA357H 3phase debugging software
- Please help me sett up my VFD
- DM860H driver and NEMA 34, 6 A, 8.5 Nm - configuration
- Chinese 'clone' version of the HY02D223B VFD AKA Type2
- 0-24VDC motor control that accepts 0-10V input?
- DIY Repair of DKC Servo Drives: Tips and Advice Needed!
- Nema 14/nema 17 driver low torque application what driver?
- Closed Loop Stepper Cable Sheild?