Activity Stream
-
Older Activity
-
3 Weeks AgoHey Folks, I'd like to rip out the interior of a boat and refit it utilising the CNC for all the woodwork. Ideally I'd like to CAD it out...2 replies | 2484 view(s)
-
1 Week Agopaul4523 started a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingUpgrading my OMIO X4 machine to an AXBB-E controller and new enclosure. I'm a novice and have tried to learn as much as possible in order to take on...5 replies | 2081 view(s)
-
3 Weeks AgoI just bought and it's really good 300 on Amazon if you apply the voucher Printing now at 600mm/s with no issues, super nice quality A...0 replies | 2253 view(s)
-
1 Week AgoHello It has been a couple of years since I built my lathe and mill, and have picked up another lathe recently to convert. A lot seems to have...2 replies | 1796 view(s)
-
1 Week AgoI have 25mm supported round rails on all 3 axis of my CNC router (for aluminium) . At the moment I have 16mm C7 Chinese ballscrews. If I were to...3 replies | 1609 view(s)
-
5 Days AgoDear all, I am new to this forum and looking for some advice about a current issue with my 8x4 CNC router. The machine is branded under the...10 replies | 755 view(s)
-
6 Days AgoI Have an Isel 4433 with a few issues.2 replies | 694 view(s)
-
3 Days AgoMuch of the internet seems to indicate that VFDs will cause RCD systems to trip out. In the UK though the whole building tends to be protected with...4 replies | 193 view(s)
-
5 Days AgoThere are no lights on illuminated the left hand side. Although the open button is not lit it does still open the door. I suspected it might be a...1 replies | 706 view(s)
-
2 Days AgoI'm just finishing a retrofit of a Triac. Used Acorn Centroid. Previously I've used SZGH, CS LABS, Pokeys and various hardware on Mach 3 and Mach...3 replies | 233 view(s)
-
13 Hours AgoHi all, I started my formal career in CAD/CAM/CNC in 1985. My machining education began when I was eight sweeping chips in my father’s injection...1 replies | 69 view(s)
-
2 Days AgoAnyone know anything about these ? Are they worth the money ?. In this case 5K in pounds ...0 replies | 233 view(s)
-
2 Days AgoTnW started a thread 8x4 CNC Router Build - Wood/Steel or Steel Frame and Component Advice in Gantry/Router Machines & BuildingAfternoon! I'm looking to build/rebuild my 8x4 CNC. I currently use one of the SheetCNC routers, it's a 25mm MDF frame which is chain-driven and...0 replies | 213 view(s)
-
6 Hours AgoNice! And welcome to the forum.1 replies | 69 view(s)
-
9 Hours AgoI honestly can't remember, as it's a good few years since I looked at it I seem to have a vague recollection that Mach supports it, but that might...3 replies | 233 view(s)
-
22 Hours AgoYou will need to be more specific than that if you would like any help ...2 replies | 694 view(s)
-
22 Hours AgoI bought a mill wired so one VFD could drive two motors with a switch select. By the time it arrived it was pulling the RCD and soon after the mill...4 replies | 193 view(s)
-
1 Day AgoMike, Should be all sorted. Let me know if there are problems and I'll resend. Regards.176 replies | 195881 view(s)
-
1 Day AgoThanks. Do you know offhand which of the controllers can manage the multi axis tool offsets without needing to regenerate code?3 replies | 233 view(s)
-
2 Days AgoMain problem with these is the EMI (electro-magnetic interference) filter on the input of the VFD - assuming that there isn't an actual fault, of...4 replies | 193 view(s)
-
2 Days AgoVFDs can trip certain RCDs, but for a typical 2.2kw VFD it isn't likely to be an issue. You could get lost down a rabbit hole of what could happen...4 replies | 193 view(s)
-
2 Days AgoNickRaven replied to a thread NEW MEMBER: New member here... Advice on CNC machine... 4-5k? in New Member IntroductionsI am new to this forum and I came across this thread whilst seeing if anyone else had had experiences with the "Itech" routers. I bought one last...5 replies | 2889 view(s)
-
2 Days AgoNo problem with mine4 replies | 193 view(s)
-
2 Days AgoI still use Emachineshop ( old version). I have yet to find such a simple to use CAD programme (free or for purchase). Just wish the 3D preview would...176 replies | 195881 view(s)
-
2 Days AgoFor multi-axis, a key thing to look at is how tool offset compensation is handled. Not all controllers can handle it for 4/5th axis, and rely on it...3 replies | 233 view(s)
-
2 Days AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionAwesome stuff. I will keep updating the tread. A10 replies | 755 view(s)
-
2 Days Agophill05 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionYes picked up a new card from cnc4you put a copy of mach on and away we went10 replies | 755 view(s)
-
2 Days AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionThanks, Yes I wouldn't be overly surprised if the issues persist after replacing the driver but I am confident it will sort out my problem. If...10 replies | 755 view(s)
-
2 Days Agophill05 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionMuch like your problem we tried changing drivers round but still had the problems, we took out the dsp and replaced the card to try Mach 3 and it...10 replies | 755 view(s)
-
2 Days AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionAbout 30 mins ago, turned on the machine, homed all axes and X moved in the positive direction rather than negative. Fault diagnosed as driver and I...10 replies | 755 view(s)
Greetings all!