Activity Stream
-
Older Activity
-
17 Hours AgoHi all, glad to be a member. Some great information on these forums! I am a fully employed mechanical CNC service engineer based in Lancashire,...0 replies | 76 view(s) -
1 Day AgoHi all, glad to be a member. Some great information on these forums! I am a fully employed mechanical CNC service engineer based in Lancashire,...0 replies | 66 view(s)
-
1 Day AgoThank you for your help 👍184 replies | 297168 view(s)
-
1 Day AgoFar more likely that the drive board has failed, causing the the fuse to blow and tripping the MCBs (might even cause a leak to earth, which would...1 replies | 129 view(s)
-
1 Day AgoI was starting my X3 recently and I'm not sure wha happened, but now it doesn't work at all. There was a pop on starting, maybe also something not...1 replies | 129 view(s)
-
2 Days AgoOk mate will keep an eye out for the new thread...3 replies | 1131 view(s) -
2 Days AgoLee Roberts replied to a thread NEW MEMBER: Glad to Join – CNC Spare Parts & Repair in New Member IntroductionsHi Tibor, welcome to the forum! You are welcome to be part of the community, however we will NOT tolerate any kind of spam and you will be removed...1 replies | 167 view(s)
-
2 Days AgoLee Roberts replied to a thread Fanuc Zero Return Procedure Sharing in Milling Machines, Builds & ConversionsTibor, welcome to the forum! Is this the start of your spam journey? I have moved your thread to the correct section and you are welcome to be...1 replies | 97 view(s)
-
2 Days AgoCNCFixtech started a thread NEW MEMBER: Glad to Join – CNC Spare Parts & Repair in New Member IntroductionsHi everyone! 👋 Glad to be a member of this forum. We are a supplier of CNC spare parts and also provide repair services – especially for FANUC,...1 replies | 167 view(s)
-
3 Days AgoCNCFixtech started a thread Fanuc Zero Return Procedure Sharing in Milling Machines, Builds & ConversionsZero Return in FANUC CNC machines is essential to creating an accurate reference point and must be performed whenever using an absolute position...1 replies | 97 view(s)
-
4 Days AgoHave you given the screw a very good inspection for any damage in that area? It could be something like a bit of dirt in the ballnut, but I'd expect...1 replies | 352 view(s)
-
4 Days AgoHi, I'm having real difficulty identifying an issue with my X axis linear motion. Af first glance, it would appear to be a mechanical issue;...1 replies | 352 view(s)
-
5 Days AgoThanks for your offer Lee. I think the fuse holder might be ok. It might be another issue and I'll start a new thread. Dave3 replies | 1131 view(s)
-
6 Days AgoHi guys, Been going down the rabbit hole of CNC automotive parts, and I’m amazed at what people are machining these days — custom valve covers,...0 replies | 380 view(s)
-
6 Days AgoDue to the cramped nature of my workshop, I decided to assemble the machine in situ. After manhandling the lighter VMC 190 out the door, I brought in...15 replies | 3913 view(s)
-
6 Days AgoMuzz, Sure can. Please send me your email address and I'll add you to Dropbox as the files are huge. Regards.184 replies | 297168 view(s)
-
1 Week AgoI used Rust-oleum hard hat top coat, it is fantastic paint. I was originally going to get the cabinet shot blasted and powered coated, but quotes...15 replies | 3913 view(s)
-
1 Week AgoThanks Lee, I have had a bit of experience but never had to do so much to a machine. The last was a Boxford 240 CNC lathe but it was in pretty good...15 replies | 3913 view(s)
-
1 Week AgoThat looks a great build, Did you spray the Cabinet with a HVLP gun or cans ?.Im just prepping a Lathe I brought a while ago and about to start...15 replies | 3913 view(s)
-
1 Week AgoLooking really good Mike, I'm going to take a punt and say you've done similar work before :thumsup:15 replies | 3913 view(s)
-
1 Week AgoHi I have the same problem, have not used in years and are just getting back into it, now I'm retired any chance on getting a copy of the old...184 replies | 297168 view(s)
-
1 Week AgoWell, folks, It's there—just a few odds and sods left to sort: reassembly, wiring, setup, cobbling together a 4th axis, and the small matter of...15 replies | 3913 view(s)
-
1 Week Agom_c replied to a thread Test post with attachments - SOMEONE PLEASE **** WITH THE FORUM! in General DiscussionLee, send us DM/Email if you want.6 replies | 1522 view(s)
-
1 Week AgoLee Roberts replied to a thread Test post with attachments - SOMEONE PLEASE **** WITH THE FORUM! in General DiscussionJust to give you a bit more info etc, the forum gets influxes of "bot traffic" we've also had some denial of service attacks previously that I...6 replies | 1522 view(s)
-
1 Week AgoLee Roberts replied to a thread Test post with attachments - SOMEONE PLEASE **** WITH THE FORUM! in General DiscussionThanks guys, will be sending an update out soon via email, thanks for baring with me, they are the only pics I had on my phone I could use to test...6 replies | 1522 view(s)
-
1 Week AgoMuzzer replied to a thread Test post with attachments - SOMEONE PLEASE **** WITH THE FORUM! in General DiscussionYes, me too for the last 2-3 days(?). Seems intermittent. Working now - nobody move suddenly!!6 replies | 1522 view(s)
-
1 Week Agograin_r replied to a thread Test post with attachments - SOMEONE PLEASE **** WITH THE FORUM! in General DiscussionHey Lee I have been getting Database errors when opening the site just incase it is linked, I assumed it was due to an update. but you have bigger...6 replies | 1522 view(s)
-
1 Week AgoWith the rogue ball screws sorted and the wonky tooling tamed, I turned my attention to the control panel. The old one was a sorry sight—rusty and...15 replies | 3913 view(s)
-
1 Week AgoOK will retry posting some of the images as they seem to not show in my previous post. Above cross section of the spindle showing the Nilos...15 replies | 3913 view(s)
-
1 Week AgoYes you are correct about wear and oversized balls, I think the thing is with tiny ball screws the balls seem to wear first as I guess the load is...15 replies | 3913 view(s)
Cnc service engineer