. .

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. 18-12-2018 #1
    Clive S's Avatar
    Lives in Marple Stockport, United Kingdom.
    Clive S
    Last Activity: 5 Hours Ago Forum Superstar, has done so much to help others, they deserve a medal. Has a total post count of 3,342. Received thanks 618 times, giving thanks to others 82 times. Made a monetary donation to the upkeep of the community. Is a beta tester for Machinists Network features.
    Quote Originally Posted by Fivetide View Post
    Thanks for the reply.. I'd like a confirmation for this from someone with a few more posts than 2 before wiring up a very expensive controller .. no disrespect intended picclock
    Yes, you can just reverse one pair of windings, you can also do it in software by inverting the the dir pulse.
    ..Clive
    The more you know, The better you know, How little you know
    Reply With Quote Reply With Quote
  2. 18-12-2018 #2
    Fivetide's Avatar
    Lives in Preston, United Kingdom.
    Fivetide
    Last Activity: 25-02-2023 Has been a member for 9-10 years. Has a total post count of 616. Received thanks 20 times, giving thanks to others 33 times. Made a monetary donation to the upkeep of the community.
    Quote Originally Posted by Clive S View Post
    Yes, you can just reverse one pair of windings, you can also do it in software by inverting the the dir pulse.
    thanks Clive I'm experimenting with GrBl panel atm couldn't figure out how to do it in the software lol I'll swap A+ to A- on your advice :)

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

    Reply With Quote Reply With Quote
  3. 18-12-2018 #3
    Fivetide's Avatar
    Lives in Preston, United Kingdom.
    Fivetide
    Last Activity: 25-02-2023 Has been a member for 9-10 years. Has a total post count of 616. Received thanks 20 times, giving thanks to others 33 times. Made a monetary donation to the upkeep of the community.
    worked a treat thanks for the help

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

    Reply With Quote Reply With Quote
  4. 18-12-2018 #4
    Clive S's Avatar
    Lives in Marple Stockport, United Kingdom.
    Clive S
    Last Activity: 5 Hours Ago Forum Superstar, has done so much to help others, they deserve a medal. Has a total post count of 3,342. Received thanks 618 times, giving thanks to others 82 times. Made a monetary donation to the upkeep of the community. Is a beta tester for Machinists Network features.
    Quote Originally Posted by Fivetide View Post
    worked a treat thanks for the help
    Always best to check. Glad you got it going
    ..Clive
    The more you know, The better you know, How little you know
    Reply With Quote Reply With Quote

  5. The Following User Says Thank You to Clive S For This Useful Post:

  6. 18-12-2018 #5
    Fivetide's Avatar
    Lives in Preston, United Kingdom.
    Fivetide
    Last Activity: 25-02-2023 Has been a member for 9-10 years. Has a total post count of 616. Received thanks 20 times, giving thanks to others 33 times. Made a monetary donation to the upkeep of the community.
    Quote Originally Posted by Clive S View Post
    Always best to check. Glad you got it going
    God advice :) I'm nearly there just got to fit and configure the hard stops - case up the electronics - fit it to the lathe and I'm ready for a test run

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Stepper Motor Wiring
    By ravihotwok in forum General Electronics
    Replies: 13
    Last Post: 26-07-2017, 10:41 AM
  2. Stepper motor tunning wiring
    By handyoodman03 in forum Stepper & Servo Motors
    Replies: 47
    Last Post: 11-01-2013, 05:49 PM
  3. Stepper motor wiring
    By Buba b in forum Stepper & Servo Motors
    Replies: 5
    Last Post: 28-03-2010, 06:16 PM
  4. Stepper Motor Wiring (Screened?)
    By pequod in forum Stepper & Servo Motors
    Replies: 19
    Last Post: 03-08-2009, 10:15 AM
  5. Reversing motor direction in Mach3
    By bruce_miranda in forum Artsoft Mach (3 & 4)
    Replies: 2
    Last Post: 16-11-2008, 06:54 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules