	Register Help Remember Me?
.	.

grace chen's Albums

works

Photos

12

Last Photo

12-12-2012
WOODWORKING CNC ROUTER

Photos

10

Last Photo

12-12-2012

TRENDING NOW
- Sensorless stall protection
  
  0 replies, latest reply by terry1956, 3 Days Ago
- Firmware not installing
  
  0 replies, latest reply by terry1956, 3 Days Ago
- DIY spindle stall monitor
  
  19 replies, latest reply by routercnc, 1 Week Ago
- New Member
  
  2 replies, latest reply by AndyGuid, 1 Week Ago
- DENFORD novaturn
  
  0 replies, latest reply by csuritattoo, 2 Weeks Ago
- Back up software
  
  1 replies, latest reply by imhim4747, 2 Weeks Ago
- Servo motor to drive spindle, good...
  
  0 replies, latest reply by terry1956, 3 Weeks Ago
- Denford orac encoder
  
  6 replies, latest reply by terry1956, 3 Weeks Ago
- Plasma torch is not lifting up...
  
  1 replies, latest reply by wickrme49, 3 Weeks Ago
- Nitram
  
  0 replies, latest reply by nitram, 3 Weeks Ago
POPULAR DISCUSSIONS
- Maximat V10P runs out
  
  34 replies, latest reply by Africanimp, 30-12-2023
- Testing The VFD, Break Resistor...
  
  31 replies, latest reply by Phil Mayor, 25-06-2024
- Novamill - Mach3
  
  29 replies, latest reply by Deck36, 29-05-2024
- Boxford 260 VMC rebuild
  
  20 replies, latest reply by Lee Roberts, 16-08-2025
- DIY spindle stall monitor
  
  19 replies, latest reply by routercnc, 1 Week Ago
- CNC plasma cutter options
  
  17 replies, latest reply by routercnc, 30-03-2025
- Wiring ATC with UC300eth 5LPT and...
  
  17 replies, latest reply by Phil Mayor, 05-04-2025
- Triac Z height issues
  
  17 replies, latest reply by andy_con, 07-12-2023
- Forum Attachments Acting Up?...
  
  14 replies, latest reply by dh42, 16-08-2025
- Blue Elephant is biting me
  
  13 replies, latest reply by m_c, 13-06-2025
- Planning my first CNC machine
  
  12 replies, latest reply by JohnHaine, 05-01-2024
- touch probe connectivity with...
  
  12 replies, latest reply by voyager1972, 09-04-2024
- Granite framed dental milling...
  
  12 replies, latest reply by Sliding Head, 13-02-2025
- Help diganosing fault with chinese...
  
  11 replies, latest reply by Ats101, 12-07-2024
- which spindle motor will work
  
  11 replies, latest reply by iamspuddy, 31-03-2024
- Closed Loop Stepper Cable Sheild?
  
  11 replies, latest reply by Phil Mayor, 05-09-2024
- BSMCEO4U board is not recognized...
  
  10 replies, latest reply by Lee Roberts, 17-12-2024
- Milling deep into 6062 T6
  
  10 replies, latest reply by Muzzer, 28-12-2024
- UC300ETH question
  
  10 replies, latest reply by Neale, 12-07-2024
- Setting up VFD to run without a...
  
  9 replies, latest reply by Stressedwoodman, 16-12-2024
CLASSIFIED ADS, BUY, SELL AND SWAP
- DENFORD novaturn
  
  0 replies, posted by csuritattoo, 2 Weeks Ago
- WinPC-NC controller with pc,...
  
  0 replies, posted by terry1956, 05-09-2025
FULL AND PART TIME EMPLOYMENT
- Cnc service engineer available for...
  
  2 replies, posted by Hayesy830, 04-07-2025