Search:

Looks great..!

Wal.

No that will be fine.

Nope, that diagram shows the analogue output AO1 referenced to 5V0, so you need to connect 5V0 to ACM (which I believe you said you already did). (or connect 5V0 and 24V0 together).

You could try...

Another diagram to expand on the one in post 39

26320

John

Similarly, gifted with an industry that embraces the old 60/40.

Right, just tried a quick experiment - I have some 2N7002's in the shed so hooked one up to a signal generator set to 1Hz (though I...

Hi Doddy

I see you changed your mind
dont worry
your original reply just pointed out we use the technique that we are happy with

I have to admit unless I am under instructions to maintain a...

Charlie,
When you do look at the cooling I found that using larger diameter water pipe greatly inreased the water flow from the pump I bought. The spindle fittings take 5mm id pipe but I get double...

You should also take a look at these spindle motors:

http://www.jian-ken.com/

probably the best engineered stuff I've seen come out of China

That looks like it is similar to the one I linked to. 1.5mm is more that enough but make sure that you securely clamp the cable to the Z axis so that there is no strain on the plug as if the plug...

5mm distance from the hard stop will function fine as the motors stop very quickly. If it was a home switch you might want a bit more as the machine over travels a bit.
Only thing to think about is...

you should be able to connect the BOB directly to the FET

25991


the 2N7000 would be an alternative FET in a smaller TO92 case

25992

John

going by figure 6 on page 5 of the pdf data
I would aim for a minimum of 5V

while the absolute maximum ratings for Vgs is +/- 30V
I would limit the maximum to about 20 V

pdf data
25990
...

... or simplify the whole thing and bin off the board, any isolation and just use the mosfets. What’s the Vgs(on) for the details?

it looks like you have a few options to try if the opto-isolator board does not work

John

looking at the photo of the opto-isolator board
it has 3K resistors fitted as shown on the chinese circuit diagram
so the output current is even more limited

with a 3K or 3.3K resistor between...

It should not run that hot
double check your not connecting 24V DC to a 24V AC coil !

which contactor do you have ?

John

Yes my bad :shame:

your wiring of the PNP N/C switches to the AXBB_E looks correct to me

having both the + & - terminals of the AXBB_E opto-isolator inputs free to wire as required
makes it easy to use the ...

Probably your mains voltage is on the high side and you are measuring the PS off load

I have used those drives I think they will take about 110vdc but you can also put AC into them straight from...

You might find the transformer has a primary rated at 220 or 230VAC and your stuffing 240 up it, with the proportionally higher secondary voltage. Under load you're going to see a reduction in...

The math is sound :-)

I found that my box section 1850x120x80x4 mm was + 2 mm bend in the middle by welding heat.

I had a +/- 1mm error in spirit level. over 1850 mm...

It all add up. so 6mm...

checkout dansonmarine on ebay.

https://m.ebay.nl/itm/282845732420

They stock it sometimes.

Grtz Bert.

1.3 kg A Pack

its where I bought mine from but that was a few years ago.

edit try here:- https://www.boatpaint.co.uk/acatalog/Boatpaint_co_uk_Shop_West_System_Epoxy_Resin_105___Hardeners_213.html

Ah ah another one in the "Free to do what ever HE likes, with who ever HE likes club.!! . . . . Wise man once told me when fall off bike get straight back on but learn what caused the fall and don't...

Charlie I've got the T-shirt been there done that in exactly the same circumstances, actually was with my best mate so possible worse if you didn't know the Twat and let me tell you buddy it's the...