CSMIO IP-M how to connect emergency stop ... help please

[SaporeCNC]

Hello JAZZ the red LED flashes 7 times in a row and the photo indicates the error but I do not understand what it can be?

Thank you !!!
regards

[JAZZCNC]

Hello JAZZ the red LED flashes 7 times in a row and the photo indicates the error but I do not understand what it can be?

Thank you !!!
regards

This indicates it's an encoder error so check the encoder wires are correct.

[SaporeCNC]

Friend all solved the shafts move perfect, it was an encoder cable that was disconnected !!!

in the next few days I connect the e-stop, the end of the race and the VFD ... any doubts you may have and you can be disturbed again with some other question

from now I appreciate your dedication and wisdom in answering my questions and solving the problems I had due to lack of experience in the construction of my cnc router

again thanks for everything
Greetings Jorge

[SaporeCNC]

Hello everyone

I mention my problem I have connected the spindle vfd and when I turn with the mach3 it only travels
at 12000 rpm and I can not vary its speed ...
Anyone know what might be happening ??

Thank you
regards

[Clive S]

Hello everyone

I mention my problem I have connected the spindle vfd and when I turn with the mach3 it only travels
at 12000 rpm and I can not vary its speed ...
Anyone know what might be happening ??

Thank you
regards

Can you give details of how you have connected it and have you changed any parameters in the VFD

[JAZZCNC]

Hello everyone

I mention my problem I have connected the spindle vfd and when I turn with the mach3 it only travels
at 12000 rpm and I can not vary its speed ...
Anyone know what might be happening ??

Thank you
regards

First have you enabled the Spindle and set Analog output pin in the plug-in. Until this is done you won't be able to control the speed.
In the plug-in there is also a setting for Acceleration/deceleration set this to 24000.
You will also need to set the pulley speeds in Mach3 and setup the spindle in ports & pins.

Also check the VFD accepts 0-10v and not 0-5v. Some VFD's can be set to use either.

[SaporeCNC]

Hello, thank you for your time

I pass the parameters that you enter in the VFD and I also add an attachment with the wiring of the VDF HY 3Kw 220v to the CSmioIPM and the data that you enter in the Mach3

I hope you can guide me and see why I turn the engine only at 12000 rpm

thank you very much
regards


Pd001 - 1
PD002 - 1
PD003 - 300 (frecuencia predeterminada)
PD004 - 300 (frecuencia nominal)
PD005 - 300 (frecuencia de gama alta)
PD008 - 220 (voltaje de gama alta)
PD009 - 15 (voltaje del extremo medio)
PD010 - 8 (voltaje de baja tensión)
PD011 - 200 (frecuencia mínima permitida)
PD014 - 4 (tiempo de aceleración)
PD015 - 6 (tiempo de desaceleración)
PD046 - 9
PD052 - 2
PD070 - 0 (entrada de control de velocidad)
PD072 - 300 (frecuencia alta)
PD141 - 220 (Voltaje nominal del husillo)
PD142 - 8.6 (Amperaje nominal del husillo)
PD143 - 2 (Número de polos)
PD144 - 3000

gracias !!!

[Clive S]

Pd001 - 1
PD002 - 1
PD003 - 300 (frecuencia predeterminada)
PD004 - 300 (frecuencia nominal)
PD005 - 300 (frecuencia de gama alta)
PD008 - 220 (voltaje de gama alta)
PD009 - 15 (voltaje del extremo medio)
PD010 - 8 (voltaje de baja tensión)
PD011 - 200 (frecuencia mínima permitida)
PD014 - 4 (tiempo de aceleración)
PD015 - 6 (tiempo de desaceleración)
PD046 - 9
PD052 - 2
PD070 - 0 (entrada de control de velocidad)
PD072 - 300 (frecuencia alta)
PD141 - 220 (Voltaje nominal del husillo)
PD142 - 8.6 (Amperaje nominal del husillo)
PD143 - 2 (Número de polos)
PD144 - 3000

check PD002 If it is set to one then check the jumper next to the screw terminals that you have to set. If it is on the right pair , the control is via the front knob. If it is on the left pair the control is via an external pot connected to the screw terminals.

PD003, 4 , 5 I think should be 400

PD142 is the current rating for the spindle if its 3Kw try about 13 2.2Kw would be about 10