Machine keeps stopping?

[piper1]

Hi Lee thank you very much for the reply.

This is a problem I've had since purchasing the machine about 18 months ago and now has returned.
I have earth the VFD to the metal enclosure, and then taken a second earth from another suitable point in the enclosure to a mains earth.
I have also ran an earth for the main frame of the CNC again to a main earth.
I’ve tested the spindle body with main frame of the machine for continuity and that’s fine.

I’m not sure if i should completely uninstall Mach3 and reinstall.
I’m a little reluctant to use machine for any projects ata the moment just in case it crashes

[Lee Roberts]

I’m a little reluctant to use machine for any projects ata the moment just in case it crashes

Ok well if your happy all is well with the earthing give the "dont ask me this again" option a try, as your describing it as an intermittent problem, plus you've added the MDF bed, I feel that it maybe a signal wire has come close to a power wire and noise is getting into the signal wire.

How isolated is the USB wire from one to the other?

[piper1]

To be honest Lee i think i should invest in a decent USB cable, i had to buy an extended on to reach the computer and didn’t pay attention to it needing ferrite rings on either end.
The USB cable is pretty exposed to several other cables between both the machine and computer, but i will move it to minimise any interference.
Lee do you know of anyone within the North west that does service router machine?

Thank you
Kev

[Lee Roberts]

To be honest Lee i think i should invest in a decent USB cable, i had to buy an extended on to reach the computer and didn’t pay attention to it needing ferrite rings on either end.
The USB cable is pretty exposed to several other cables between both the machine and computer, but i will move it to minimise any interference.
Lee do you know of anyone within the North west that does service router machine?

Thank you
Kev

I new it ;-)

A decent USB cable can help but if you can move it away from the other cables you may not need a new one, remember you've had your machine working fine at times, this tells us the setup has potential.

No sorry I dont but we have members all over the UK so you could put up a request in the Projects, Jobs & Requests forum.

[piper1]

Did a couple of test runs this afternoon, one with the spindle running and one without
Both ran the exact program, same length of time etc and not not a glitch in sight.
Both test ran flawlessly, i was so made up.

The only thing i did in the hope to remedy the fault with the machine stopping during programs was to move the USB cable away from any other possible interference's (cables).

Going to run the same program again tomorrow with the machine cutting this time , fingers crossed.

Thank you for the advise Lee.

[Clive S]

I think you said you said that you had an extension to the usb lead if so buy a new lead long enough the shorter the better. make sure it is a good quality one.

With an extension you are creating another joint

[piper1]

Going to order one on the morning Clive, cheers.
Keeping my fingers crossed for tomorrows test run.

[Lee Roberts]

Did a couple of test runs this afternoon, one with the spindle running and one without
Both ran the exact program, same length of time etc and not not a glitch in sight.
Both test ran flawlessly, i was so made up.

The only thing i did in the hope to remedy the fault with the machine stopping during programs was to move the USB cable away from any other possible interference's (cables).

Going to run the same program again tomorrow with the machine cutting this time , fingers crossed.

Thank you for the advise Lee.

Sweeeet!

Hopfully the next test works fine, Clive is right as well grab yourself a nice USB cable about the right length, you dont need to spend crazy money getting some gold plated, braided bad boy, something like this should do: Hama USB Cable Blue 5m

Keep us posted its nice to know when something gets fixed :)

[piper1]

Ran the third test this afternoon to confirm that everything was still working ok and it ran perfectly without missing a beat.
Still using the old USB cable until the new one arrive.
Managed to sort out a couple of ferrite rings so added them to the old cable.

Thank you so much to everyone for all the support i received i really do appreciate it.

Cheers
Kev

[Clive S]

Remember that too many earths may result in a ground loop. so take the earth to just one place (think star point) I there a ground between the pc and controller try a different usb lead.