Denford Triac VMC with ATC Conversion / Fix

**Chaz** · 16-03-2017

Originally Posted by andy_con

So you have upgraded the spindle to a Panasonic one? How does it work with atc?

I'm gagging to upgrade my spindle, I've got money just no options

Yep. It works well. I dont use my ATC often but functionally it works. I can do some improvements to it for fine tuning but the machine is now running at minimum as good as it would have when new.

Where are you based? You are welcome to come look at the bits.

**andy_con** · 16-03-2017

Originally Posted by Chaz

Yep. It works well. I dont use my ATC often but functionally it works. I can do some improvements to it for fine tuning but the machine is now running at minimum as good as it would have when new.

Where are you based? You are welcome to come look at the bits.

So spindle speed? How have you got it to work?

What kind of setup?

The triac has a slightly different atc seti
Up the. Most with its spindle and powered draw bar

I'm in Essex?

**Chaz** · 16-03-2017

Direct motor replacement, 4400 rpm due to slight change in gearing.

Im in West London - UB108TE, feel free to pop around, Im home Saturday if you want to see my mess.

Ill take some pics anyways to share.

**xiteamxi** · 16-03-2017

What did you end up with an m6 macro for the atc? Any chance you could post it up?

**Chaz** · 16-03-2017

Originally Posted by xiteamxi

What did you end up with an m6 macro for the atc? Any chance you could post it up?

I had an initial bit of code provided however it did not work. My code is poor and doesnt care for the status of limit switches or even counting of the ATC. It does however work so can post.

**xiteamxi** · 17-03-2017

Originally Posted by Chaz

I had an initial bit of code provided however it did not work. My code is poor and doesnt care for the status of limit switches or even counting of the ATC. It does however work so can post.

Better then what i've come up with so far i'm sure, if you get a chance to post it id appreciate it,or if anyone else has a working m6 atc macro..

**Chaz** · 17-03-2017

Originally Posted by xiteamxi

Better then what i've come up with so far i'm sure, if you get a chance to post it id appreciate it,or if anyone else has a working m6 atc macro..

Send me a PM with your email address so I can also explain a few bits about it.

**andy_con** · 17-03-2017

I have full triac m6 macro

Originally Posted by xiteamxi

Better then what i've come up with so far i'm sure, if you get a chance to post it id appreciate it,or if anyone else has a working m6 atc macro..

**andy_con** · 16-03-2017

Originally Posted by Chaz

Direct motor replacement, 4400 rpm due to slight change in gearing.

Im in West London - UB108TE, feel free to pop around, Im home Saturday if you want to see my mess.

Ill take some pics anyways to share.

Not knocking ya build or anything but triac comes with a 4000rpm motor so that's not really an upgrade.

I want to min of 10000rpm

What electronics do you have? I'm assuming your running mach?

I have full drawings to upgrade the atc to 10 tools just never got round to making it. It's just a new disk/bit that holds the tools and stepper motor to spin the disk

**Chaz** · 16-03-2017

Originally Posted by andy_con

Not knocking ya build or anything but triac comes with a 4000rpm motor so that's not really an upgrade.

I want to min of 10000rpm

What electronics do you have? I'm assuming your running mach?

I have full drawings to upgrade the atc to 10 tools just never got round to making it. It's just a new disk/bit that holds the tools and stepper motor to spin the disk

It wasnt meant as an upgrade. It was meant to get me up and running again. The DC motor was failing and I had to make do with something as I am using the Triac to make parts for my new machine.

10K is possible, of course, but its a fairly big undertaken and not a 'hot swap' like what I did.

I am running with CS Labs - Mach 3 - Servos all round for all axis.